Skip to Content

Applicable Models

This information is for the following models:
  • NEX-7K
  • NEX-7

About this download

Thank you for your continued interest in Sony products.
Sony is offering a firmware update for Interchangeable Lens Digital Camera NEX-7 version 1.03.

Improvements after firmware upgrade

  • Addition of AF drive system for movies
    AF drive system for movie was added in order to enhance the scalability of future E-mount systems. This feature ensures a higher degree of flexibility in the design of future E-mount lenses. We will be able to provide lenses that can even better satisfy our customers.

Improvements from previous version (1.01 to 1.02) 

  • Applies automatic compensation to SELP1650
  • Makes SELP1650 retract immediately after turning off the camera

Improvements from previous version (1.00 to 1.01)

  • Addition of capability to enable or disable MOVIE button.
  • Addition of exposure settings of bracket shooting (three frames /1.0EV,2.0EV, 3.0EV).
  • Improvement of response of showing auto review image.
  • Improvement of image quality when using a wide angle lens.
  • Improvement of indication when setting Flexible Spot.

How to check the firmware version

  1. Select Menu → Setup → Version on the camera.
  2. The firmware version is displayed. If your firmware version is Ver. 1.03 or later, the upgrade is not required.

Preparing for firmware update

System requirements for a computer

Supported OS

  • Windows 10
  • Windows 8.1
  • Windows 7 SP1

Other system requirements

  • Hard disk space: 200MB or more
  • RAM: 512MB or more
    * Please close all other application software before upgrading the firmware.

Other Items

  • USB cable supplied with the camera

    Note: Update functionality is not guaranteed with any other USB cable.
  • Power source for the camera

    Fully charged rechargeable battery pack NP-FW50 or AC adaptor AC-PW20 (sold separately)

    Note: The upgrade can be performed only when the remaining battery level is (three marks) or more. We recommend that you use a fully charged battery or the AC adaptor AC-PW20 (sold separately).

File Info

File Name

  • Update_NEX7V103.exe

File Version

  • 1.03

File Size

  • 50.4MB

Release Date

  • 2013-08-27

System Requirements

  • Windows 10
  • Windows 7
  • Windows 8 32bit
  • Windows 8 64bit

Install

Details

IMPORTANT:

  • When performing the firmware upgrade, please use a fully charged rechargeable battery pack NP-FW50 or the AC adaptor AC-PW20 (sold separately).
  • Do not remove the battery or AC adaptor during the upgrade; otherwise, the camera may become inoperable due to the sudden power shutdown.
  • Remove the memory card from the camera beforehand.
  • When using an A-mount lens with the LA-EA2 Mount Adaptor (sold separately) and setting to use the AF Micro Adj. function, the registered value is reset.

Start Firmware Updater

  1. Download the file to your computer.

    For Windows 8 users:
    Under the initial settings of Internet Explorer, the update file will be saved in the Downloads folder. Click the Desktop tile from the Start screen and find the downloaded file in the Downloads folder by using Explorer.

  2. Close all currently running programs on your computer.
    Double-click Update_NEX7V103.exe to start up Firmware Updater.

     
  3. Check the USB connection mode

    Select Menu → Setup → USB Connection on the camera, and confirm Mass Storage is selected. If the mode other than Mass Storage is selected, please select Mass Storage.

  4. Connect the camera to the computer with the supplied USB cable.
    Note: When the camera is connected to the computer, the LCD screen of the camera turns off. Please proceed to the next step.

    If the computer cannot find the camera, the message “ Could not find the camera for this update.” appears on the computer display. Try the following if this happens.
    - Disconnect the USB cable and connect it again.
    - If the computer has multiple USB terminals, try with the other terminals. (Your computer may have some USB terminals on the backside.)
  5. Confirm is displayed on the task tray at the lower right corner of the computer screen.
    Note: If the icon is not displayed on the task tray, please proceed to the next step.
  6. After confirming the above, click Next on Firmware Updater.
    The screen below appears on Firmware Updater.


    Camera’s LCD screen



    Note: From this step onwards, never turn off the camera until the firmware upgrade is completed.
  7. After confirming the screens on the above steps, click Next. The current version and the version after the upgrade appear on the lower left part of the screen.

    Upgrade is required




    If the screen below appears, the upgrade is not required. According to the message, stop the USB connection and click Finish. Turn off the camera, remove the battery pack or the AC adaptor, and then turn on the camera again.

    Upgrade is not required

  8. Click on the task tray at the lower right corner of the computer screen to stop the USB connection.

    Notes:
    - Please keep the USB cable connected even after stopping the USB connection on the computer with the above operation.
    - If the icon is not displayed on the task tray, please proceed to the next step.

  9. Press the center of the control wheel to reset the camera.

    Camera’s LCD screen



    Camera control wheel



    Note: The screen turns off when the center of the control wheel is pressed. Please proceed to the next step.
  10. Click Next on Firmware Updater

  11. After resetting, reconnection of the camera is verified, and the screen below appears.

  12. Click Run to start the upgrade. The progress bar appears while upgrading (approximately 5 minutes).

    Note: Never turn off the camera nor disconnect the USB cable while upgrading.
  13. When the upgrade is completed, the screen below appears. Click Finish and disconnect the USB cable.

  14. Click on the task tray at the lower right corner of the computer screen to stop the USB connection.
    Note: If the icon is not displayed on the task tray, please proceed to the next step.
  15. Disonnect the USB cable. Turn off the camera, remove the battery pack or the AC adaptor, and then turn on the camera again.

Check the firmware version

  1. Select Menu → Setup → Version on the camera.
  2. The firmware version is displayed. The firmware upgrade was completed successfully if Ver. 1.03 is displayed.